please dont rip this site

Scenix Lib IO OSI2 Serial Stdinc.src

	; *********************************************************************************
	; Assembler directives:
	;	high speed external osc, turbo mode, 8-level stack, and extended option reg.
	;
	;	SX18/20/28 - 4 pages of program memory and 8 banks of RAM enabled by default.
	;	SX48/52 - 8 pages of program memory and 16 banks of RAM enabled by default.
	;                
	;*********************************************************************************

IFDEF SX_Key 				;SX-Key Directives
  IFDEF SX18_20				;SX18AC or SX20AC device directives for SX-Key
		device	SX18L,oschs2,turbo,stackx_optionx
		SX_TYPE=0
  ENDIF
  IFDEF SX28				;SX28AC device directives for SX-Key		
		device	SX28L,oschs2,turbo,stackx_optionx
		SX_TYPE=0
  ENDIF
  IFDEF SX48_52_ES			;SX48BD/ES or SX52BD/ES device directives for SX-Key
		device	oschs,turbo,stackx,optionx
		SX_TYPE=1
  ELSE
    IFDEF SX48_52				;SX48/52/BD device directives for SX-Key
		device	oschs2
		SX_TYPE=1
    ENDIF
  ENDIF
		freq	50_000_000
ELSE  					;SASM Directives
  IFDEF SX18_20				;SX18AC or SX20AC device directives for SASM
		device	SX18,oschs2,turbo,stackx,optionx
		SX_TYPE=0
  ENDIF
  IFDEF SX28				;SX28AC device directives for SASM
		device	SX28,oschs2,turbo,stackx,optionx
		SX_TYPE=0
  ENDIF
  IFDEF SX48_52_ES			;SX48BD/ES or SX52BD/ES device directives for SASM
		device	SX52,oschs,turbo,stackx,optionx
		SX_TYPE=1
  ELSE
    IFDEF SX48_52			;SX48BD or SX52BD device directives for SASM
		device	SX52,oschs2  
		SX_TYPE=1
    ENDIF
  ENDIF
ENDIF

;*****************************************************************************************
; Macros
;*****************************************************************************************

	;*********************************************************************************
	; Macro: _bank
	; Sets the bank appropriately for all revisions of SX.
	;
	; This is required since the bank instruction has only a 3-bit operand, it cannot
	; be used to access all 16 banks of the SX48/52. For this reason FSR.4 (for SX48/52BD/ES)
	; or FSR.7 (SX48/52bd production release) needs to be set appropriately, depending
	; on the bank address being accessed. This macro fixes this.
	;
	; So, instead of using the bank instruction to switch between banks, use _bank instead.
	; 
	;*********************************************************************************
_bank	macro	1
	bank	\1

	IFDEF SX48_52
	  IFDEF SX48_52_ES
	    IF \1 & %00010000		;SX48BD/ES and SX52BD/ES (engineering sample) bank instruction
		setb	fsr.4		;modifies FSR bits 5,6 and 7. FSR.4 needs to be set by software.
	    ENDIF
	  ELSE
	    IF \1 & %10000000		;SX48BD and SX52BD (production release) bank instruction 
		setb	fsr.7		;modifies FSR bits 4,5 and 6. FSR.7 needs to be set by software.
	    ELSE
		clrb	fsr.7
	    ENDIF
	  ENDIF
	ENDIF
	endm

	;*********************************************************************************
	; Macro: _mode
	; Sets the MODE register appropriately for all revisions of SX.
	;
	; This is required since the MODE (or MOV M,#) instruction has only a 4-bit operand. 
	; The SX18/20/28AC use only 4 bits of the MODE register, however the SX48/52BD have 
	; the added ability of reading or writing some of the MODE registers, and therefore use
	; 5-bits of the MODE register. The  MOV M,W instruction modifies all 8-bits of the 
	; MODE register, so this instruction must be used on the SX48/52BD to make sure the MODE
	; register is written with the correct value. This macro fixes this.
	;
	; So, instead of using the MODE or MOV M,# instructions to load the M register, use
	;  _mode instead.
	; 
	;*********************************************************************************
_mode	macro	1
	IFDEF SX48_52
		mov	w,#\1		;loads the M register correctly for the SX48BD and SX52BD
		mov	m,w
	ELSE
		mov	m,#\1		;loads the M register correctly for the SX18AC, SX20AC
					;and SX28AC
	ENDIF
	endm

_clear	macro
	;*********************************************************************************
	; Clear all Data RAM locations
	;*********************************************************************************
IFDEF SX48_52   				;SX48/52 RAM clear routine
		mov	w,#$0a			;reset all ram starting at $0A
		mov	fsr,w
:zero_ram	clr	ind			;clear using indirect addressing
		incsz	fsr			;repeat until done
		jmp	:zero_ram

		_bank	bank0			;clear bank 0 registers
		clr	$10
		clr	$11
		clr	$12
		clr	$13
		clr	$14
		clr	$15
		clr	$16
		clr	$17
		clr	$18
		clr	$19
		clr	$1a
		clr	$1b
		clr	$1c
		clr	$1d
		clr	$1e
		clr	$1f

ELSE     					;SX18/20/28 RAM clear routine
		clr	fsr			;reset all ram banks
:zero_ram	sb	fsr.4			;are we on low half of bank?
		setb	fsr.3			;If so, don't touch regs 0-7
		clr	ind			;clear using indirect addressing
		incsz	fsr			;repeat until done
		jmp	:zero_ram
ENDIF
endm

;*****************************************************************************************
; Data Memory address definitions
; These definitions ensure the proper address is used for banks 0 - 7 for 2K SX devices
; (SX18/20/28) and 4K SX devices (SX48/52). 
;*****************************************************************************************

IFDEF SX48_52
	global_org	=	$0A
	bank0 	=	$00	;bank 0 address on SX52
	bank1 	=	$10	;bank 1 address on SX52
	bank2 	=	$20	;bank 2 address on SX52
	bank3 	=	$30	;bank 3 address on SX52
	bank4 	=	$40	;bank 4 address on SX52
	bank5 	=	$50	;bank 5 address on SX52
	bank6 	=	$60	;bank 6 address on SX52
	bank7 	=	$70	;bank 7 address on SX52
	bank8 	=	$80	;bank 8 address on SX52
	bank9 	=	$90	;bank 9 address on SX52
	bankA 	=	$A0	;bank A address on SX52
	bankB 	=	$B0	;bank B address on SX52
	bankC 	=	$C0	;bank C address on SX52
	bankD 	=	$D0	;bank D address on SX52
	bankE 	=	$E0	;bank E address on SX52
	bankF 	=	$F0	;bank F address on SX52
ELSE
	global_org	=	$08
	bank0	=	$10	;bank 0 address on SX28
	bank1	=	$30	;bank 1 address on SX28
	bank2	=	$50	;bank 2 address on SX28
	bank3	=	$70	;bank 3 address on SX28
	bank4	=	$90	;bank 4 address on SX28
	bank5	=	$B0	;bank 5 address on SX28
	bank6	=	$D0	;bank 6 address on SX28
	bank7	=	$F0	;bank 7 address on SX28
ENDIF

IFDEF SX48_52
	;*********************************************************************************
	; SX48BD/52BD Mode addresses
	; *On SX48BD/52BD, most registers addressed via mode are read and write, with the
	; exception of CMP and WKPND which do an exchange with W.
	;*********************************************************************************
; Timer (read) addresses
TCPL_R		equ	$00		;Read Timer Capture register low byte
TCPH_R		equ	$01		;Read Timer Capture register high byte
TR2CML_R	equ	$02		;Read Timer R2 low byte
TR2CMH_R	equ	$03		;Read Timer R2 high byte
TR1CML_R	equ	$04		;Read Timer R1 low byte
TR1CMH_R	equ	$05 		;Read Timer R1 high byte
TCNTB_R		equ	$06		;Read Timer control register B
TCNTA_R		equ	$07		;Read Timer control register A

; Exchange addresses
CMP		equ	$08		;Exchange Comparator enable/status register with W
WKPND		equ	$09		;Exchange MIWU/RB Interrupts pending with W

; Port setup (read) addresses
WKED_R		equ	$0A		;Read MIWU/RB Interrupt edge setup, 0 = falling, 1 = rising
WKEN_R		equ	$0B		;Read MIWU/RB Interrupt edge setup, 0 = enabled, 1 = disabled
ST_R		equ	$0C		;Read Port Schmitt Trigger setup, 0 = enabled, 1 = disabled
LVL_R		equ	$0D		;Read Port Schmitt Trigger setup, 0 = enabled, 1 = disabled
PLP_R		equ	$0E		;Read Port Schmitt Trigger setup, 0 = enabled, 1 = disabled
DDIR_R		equ	$0F		;Read Port Direction

; Timer (write) addresses
CLR_TMR		equ	$10		;Resets 16-bit Timer
TR2CML_W	equ	$12		;Write Timer R2 low byte
TR2CMH_W	equ	$13		;Write Timer R2 high byte
TR1CML_W	equ	$14		;Write Timer R1 low byte
TR1CMH_W	equ	$15 		;Write Timer R1 high byte
TCNTB_W		equ	$16		;Write Timer control register B
TCNTA_W		equ	$17		;Write Timer control register A

; Port setup (write) addresses
WKED_W		equ	$1A		;Write MIWU/RB Interrupt edge setup, 0 = falling, 1 = rising
WKEN_W		equ	$1B		;Write MIWU/RB Interrupt edge setup, 0 = enabled, 1 = disabled
ST_W		equ	$1C		;Write Port Schmitt Trigger setup, 0 = enabled, 1 = disabled
LVL_W		equ	$1D		;Write Port Schmitt Trigger setup, 0 = enabled, 1 = disabled
PLP_W		equ	$1E		;Write Port Schmitt Trigger setup, 0 = enabled, 1 = disabled
DDIR_W		equ	$1F		;Write Port Direction

ELSE

	;*********************************************************************************
	; SX18AC/20AC/28AC Mode addresses
	; *On SX18/20/28, all registers addressed via mode are write only, with the exception of
	; CMP and WKPND which do an exchange with W.
	;*********************************************************************************
; Exchange addresses
CMP		equ	$08		;Exchange Comparator enable/status register with W
WKPND		equ	$09		;Exchange MIWU/RB Interrupts pending with W

; Port setup (read) addresses
WKED_W		equ	$0A		;Write MIWU/RB Interrupt edge setup, 0 = falling, 1 = rising
WKEN_W		equ	$0B		;Write MIWU/RB Interrupt edge setup, 0 = enabled, 1 = disabled
ST_W		equ	$0C		;Write Port Schmitt Trigger setup, 0 = enabled, 1 = disabled
LVL_W		equ	$0D		;Write Port Schmitt Trigger setup, 0 = enabled, 1 = disabled
PLP_W		equ	$0E		;Write Port Schmitt Trigger setup, 0 = enabled, 1 = disabled
DDIR_W		equ	$0F		;Write Port Direction
ENDIF

	;*********************************************************************************
	; SX18AC/20AC/28AC RTCC bit flags
	;*********************************************************************************
RTCC_ON		=	%10000000	;Enables RTCC at address $01 (RTW hi)
					;*WREG at address $01 (RTW lo) by default
RTCC_ID		=	%01000000	;Disables RTCC edge interrupt (RTE_IE hi)
					;*RTCC edge interrupt (RTE_IE lo) enabled by default
RTCC_INC_EXT	=	%00100000	;Sets RTCC increment on RTCC pin transition (RTS hi)
					;*RTCC increment on internal instruction (RTS lo) is default
RTCC_FE		=	%00010000	;Sets RTCC to increment on falling edge (RTE_ES hi)
					;*RTCC to increment on rising edge (RTE_ES lo) is default
RTCC_PS_ON	=	%00000000	;Assigns prescaler to RTCC (PSA lo)
RTCC_PS_OFF	=	%00001000	;Assigns prescaler to RTCC (PSA lo)
PS_000		=	%00000000	;RTCC = 1:2, WDT = 1:1
PS_001		=	%00000001	;RTCC = 1:4, WDT = 1:2
PS_010		=	%00000010	;RTCC = 1:8, WDT = 1:4
PS_011		=	%00000011	;RTCC = 1:16, WDT = 1:8
PS_100		=	%00000100	;RTCC = 1:32, WDT = 1:16
PS_101		=	%00000101	;RTCC = 1:64, WDT = 1:32
PS_110		=	%00000110	;RTCC = 1:128, WDT = 1:64
PS_111		=	%00000111	;RTCC = 1:256, WDT = 1:128


file: /Techref/scenix/lib/io/osi2/serial/stdinc.src, 10KB, , updated: 2004/11/19 16:16, local time: 2024/10/14 10:06,
TOP NEW HELP FIND: 
98.80.143.34:LOG IN
©2024 PLEASE DON'T RIP! THIS SITE CLOSES OCT 28, 2024 SO LONG AND THANKS FOR ALL THE FISH!

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF="http://techref.massmind.org/techref/scenix/lib/io/osi2/serial/stdinc.src"> scenix lib io osi2 serial stdinc</A>

Did you find what you needed?

 

Welcome to massmind.org!

 

Welcome to techref.massmind.org!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .