please dont rip this site
/*********************************************************************************************/
/* Program : COMMDEFS.H */
/* Function : Common macros and defines for PIC app’s not defined in pic.h */
/* Author : John F. Fitter B.E. */
/* */
/* Copyright © 1997 Eagle Air Australia Pty. Ltd. All rights reserved */
/*********************************************************************************************/

#ifndef _COMMDEFS_H
#define _COMMDEFS_H

#include <pic.h>

// General PIC macros (additional to pic.h)
#define clrwdt() CLRWDT()

// Macro to define the ID bytes
#define __ID(a,b,c,d) asm("\tpsect absdata, abs ovrld, delta=2"); \
		asm("\tglobal id_bytes"); \
		asm("\torg 0x2000"); \
		asm("id_bytes"); \
		asm("\tdb "___mkstr(a)); \
		asm("\tdb "___mkstr(b)); \
		asm("\tdb "___mkstr(c)); \
		asm("\tdb "___mkstr(d))
		
// General macros
#define HIBYTE(intValue) ((intValue)>>8)
#define LOBYTE(intValue) ((intValue)&0xff)
#define HINIBBLE(charValue) ((charValue)>>4)
#define LONIBBLE(charValue) ((charValue)&0xf)

// Common bit defines
#define B_IN 1
#define B_OUT 0
#define B_HIGH 1
#define B_LOW 0

// Common byte defines
#define W_IN 0xff
#define W_OUT 0
#define W_HIGH 0xff
#define W_LOW 0

// Common peripheral control defines
#define P_ON 1
#define P_OFF 0

// Common user interface defines
#define I_UP 1
#define I_DOWN 0

// Logical defines
#define TRUE 1
#define FALSE 0
#define true TRUE
#define false FALSE

// Hardware pullup defines
#define port_b_pullups(flag) RBPU=flag==0

// ASCII control character defines (useful for comms)
#define A_NUL 0
#define A_SOH 1
#define A_STX 2
#define A_ETX 3
#define A_EOT 4
#define A_ENQ 5
#define A_ACK 6
#define A_BEL 7
#define A_BS 8
#define A_HT 9
#define A_LF 0xa
#define A_VT 0xb
#define A_FF 0xc
#define A_CR 0xd
#define A_SO 0xe
#define A_SI 0xf
#define A_DLE 0x10
#define A_DC1 0x11
#define A_DC2 0x12
#define A_DC3 0x13
#define A_DC4 0x14
#define A_NAK 0x15
#define A_SYN 0x16
#define A_ETB 0x17
#define A_CAN 0x18
#define A_EM 0x19
#define A_SUB 0x1a
#define A_ESC 0x1b
#define A_FS 0x1c
#define A_GS 0x1d
#define A_RS 0x1e
#define A_US 0x1f

// Timer 0 defines
#define RTCC_INTERNAL 0 // rtcc_state values (OR together)
#define RTCC_EXT_L_TO_H 0x20
#define RTCC_EXT_H_TO_L 0x30

#define RTCC_DIV_2 0 // ps_state values (OR together)
#define RTCC_DIV_4 1
#define RTCC_DIV_8 2
#define RTCC_DIV_16 3
#define RTCC_DIV_32 4
#define RTCC_DIV_64 5
#define RTCC_DIV_128 6
#define RTCC_DIV_256 7
#define WDT_18MS 8
#define WDT_36MS 9
#define WDT_72MS 0xa
#define WDT_144MS 0xb
#define WDT_288MS 0xc
#define WDT_576MS 0xd
#define WDT_1152MS 0xe
#define WDT_2304MS 0xf

#define setup_counters(rtcc_state,ps_state) OPTION=(OPTION&0xc0)|rtcc_state|ps_state
#define get_rtcc() TMR0
#define set_rtcc(tvalue) TMR0=tvalue
#define get_timer0() get_rtcc()
#define set_timer0(tvalue) set_rtcc(tvalue)

// Timer 1 defines
#define T1_ENABLED 1 // timer 1 modes (OR together)
#define T1_INTERNAL 1
#define T1_EXTERNAL 7
#define T1_EXTERNAL_SYNC 3
#define T1_CLK_OUT 8
#define T1_DIV_BY_1 0
#define T1_DIV_BY_2 0x10
#define T1_DIV_BY_4 0x20
#define T1_DIV_BY_8 0x30

static unsigned int TMR1 @ 0x0E;
static unsigned int CCPR1 @ 0x15;
static unsigned int CCPR2 @ 0x1B;

#define setup_timer_1(mode) T1CON=mode
#define enable_timer_1(state) TMR1ON=state
#define get_timer1() TMR1
#define set_timer1(tvalue) TMR1=tvalue

// Timer 2 defines
#define T2_DISABLED 0 // timer 2 modes (OR together)
#define T2_DIV_BY_1 4 // T2_DISABLED must be on its own
#define T2_DIV_BY_4 5 // postscale is 1 to 16
#define T2_DIV_BY_16 7
#define setup_timer_2(mode,postscale) T2CON=mode|((postscale-1)<<3)
#define get_timer2() TMR2
#define set_timer2(tvalue) TMR2=tvalue

// CCP defines

static volatile bit CCP1 @ (unsigned)&PORTC*8+2;  // CCP1 port pin
static volatile bit CCP2 @ (unsigned)&PORTC*8+1;  // CCP2 port pin

#define CCP_OFF 0
#define CCP_CAPTURE_FE 4
#define CCP_CAPTURE_RE 5
#define CCP_CAPTURE_DIV_4 6
#define CCP_CAPTURE_DIV_16 7
#define CCP_COMPARE_SET_ON_MATCH 8
#define CCP_COMPARE_CLR_ON_MATCH 9
#define CCP_COMPARE_INT 0xa
#define CCP_COMPARE_RESET_TIMER 0xb
#define CCP_PWM 0xc
#define CCP_PWM_PLUS_1 0x1c
#define CCP_PWM_PLUS_2 0x2c
#define CCP_PWM_PLUS_3 0x3c

#define setup_ccp1(mode) CCP1CON=mode
#define setup_ccp2(mode) CCP2CON=mode
#define set_ccp1(cvalue) CCPR1=cvalue
#define set_ccp2(cvalue) CCPR2=cvalue
#define get_ccp1() CCPR1
#define get_ccp2() CCPR2

// Interrupt defines
#define GLOBAL 0x80
//#define ADC_DONE
#define RTCC_ZERO 0x20
#define RB_CHANGE 0x08
#define EXT_INT 0x10
#define INT_TIMER1 0x0100
#define INT_TIMER2 0x0200
#define INT_CCP1 0x0400
#define INT_CCP2 0x10000
#define INT_SSP 0x0800
#define INT_PSP 0x8000
#define INT_RDA 0x2000
#define INT_TBE 0x1000

#define enable_peripheral_interrupts() PEIE=1
#define enable_global_interrupts() GIE=1
#define enable_interrupts(level) \
		INTCON|=(level)&0xff; \
		PIE1|=((level)>>8)&0xff; \
		PIE2|=(level)>>16
#define enable_rtcc_interrupt() T0IE=1

#define disable_peripheral_interrupts() PEIE=0
#define disable_global_interrupts() do GIE=0;while(GIE)
#define disable_interrupts(level) \
		INTCON&=~((level)&0xff); \
		PIE1&=~(((level)>>8)&0xff); \
		PIE2&=~((level)>>16)
#define disable_rtcc_interrupt() T0IE=0

// USART defines
#define SER_MASTER 0x80
#define SER_9BIT 0x40
#define SER_TX_ENABLE 0x20
#define SER_SYNCHRONOUS 0x10
#define SER_HIGH_BAUD 4
#define SER_TSR_EMPTY 2
#define SER_ENABLE 0x80
#define SER_RX_SGL 0x20
#define SER_RX_CON 0x10

#define kbhit() RCIF

#define set_lo_baud(baud) SPBRG=(unsigned char)((2*(long)_CLOCK_/64+(long)baud)/2/\
		(long)baud-1);TXSTA &= ~SER_HIGH_BAUD
#define set_hi_baud(baud) SPBRG=(unsigned char)((2*(long)_CLOCK_/16+(long)baud)/2/\
		(long)baud-1);TXSTA |= SER_HIGH_BAUD
		
#define setup_usart_async8_lo(baud) \
		TRISC |= 0xc0;\
		TXSTA=SER_MASTER|SER_TX_ENABLE|SER_TSR_EMPTY; \
		RCSTA=SER_ENABLE|SER_RX_CON; \
		set_lo_baud(baud)
		
#define setup_usart_async9_lo(baud) \
		TRISC |= 0xc0;\
		TXSTA=SER_MASTER|SER_TX_ENABLE|SER_TSR_EMPTY|SER_9BIT; \
		RCSTA=SER_ENABLE|SER_RX_CON|SER_9BIT; \
		set_lo_baud(baud)

#define setup_usart_async8_hi(baud) \
		TRISC |= 0xc0;\
		TXSTA=SER_MASTER|SER_TX_ENABLE|SER_TSR_EMPTY; \
		RCSTA=SER_ENABLE|SER_RX_CON; \
		set_hi_baud(baud)

#define setup_usart_async9_hi(baud) \
		TRISC |= 0xc0;\
		TXSTA=SER_MASTER|SER_TX_ENABLE|SER_TSR_EMPTY|SER_9BIT; \
		RCSTA=SER_ENABLE|SER_RX_CON|SER_9BIT; \
		set_hi_baud(baud)

static volatile bit txd @ (unsigned)&PORTC*8+6;  // USART serial data out pin
static volatile bit rxd @ (unsigned)&PORTC*8+7;  // USART serial data in pin

// SPI defines
#define SPI_MASTER 0x20
#define SPI_SLAVE 0x24
#define SPI_SS_DISABLED 0x25
#define SPI_L_TO_H 0
#define SPI_H_TO_L 0x10
#define SPI_CLK_DIV_4 0
#define SPI_CLK_DIV_16 1
#define SPI_CLK_DIV_64 2
#define SPI_CLK_T2 3
#define spi_enable(en) SSPEN=!!en // enables the spi
#define spi_data_is_in() BF // tests the buffer full bit

static volatile bit sdo @ (unsigned)&PORTC*8+5;  // serial data out pin
static volatile bit sdo_dir @ (unsigned)&TRISC*8+5;  // serial data out direction bit
static volatile bit sdi @ (unsigned)&PORTC*8+4;  // serial data in pin
static volatile bit sdi_dir @ (unsigned)&TRISC*8+4;  // serial data in direction bit
static volatile bit sck @ (unsigned)&PORTC*8+3;  // serial clock pin
static volatile bit sck_dir @ (unsigned)&TRISC*8+3;  // serial clock direction bit
static volatile bit ss_dir @ (unsigned)&TRISA*8+5;  // synchronous slave mode enable bit
static volatile bit BF @ (unsigned)&SSPSTAT*8+0;  // spi buffer full bit

#endif // COMMDEFS_H



file: /Techref/microchip/language/c/comdefs_h.htm, 7KB, , updated: 2001/2/2 16:21, local time: 2024/12/22 23:22,
TOP NEW HELP FIND: 
18.227.46.87:LOG IN

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF="http://techref.massmind.org/techref/microchip/language/c/comdefs_h.htm"> microchip language c comdefs_h</A>

After you find an appropriate page, you are invited to your to this massmind site! (posts will be visible only to you before review) Just type a nice message (short messages are blocked as spam) in the box and press the Post button. (HTML welcomed, but not the <A tag: Instead, use the link box to link to another page. A tutorial is available Members can login to post directly, become page editors, and be credited for their posts.


Link? Put it here: 
if you want a response, please enter your email address: 
Attn spammers: All posts are reviewed before being made visible to anyone other than the poster.
Did you find what you needed?

 

Welcome to massmind.org!

 

Welcome to techref.massmind.org!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .