please dont rip this site

Language Pcl LJ1884.ASC

USING  THE BZ COMMAND

    
     The BZ command or Bezier Absolute command draws bezier
     curves using absolute coordinates. It uses the current
     pen position as the first control point, and specifies
     the other three control points as absolute coordinates.
     For more information see the PCL 5 Printer Language
     Technical Reference Manual.
     
          Note:  The Bezier command is not
                 supported in any printers prior
                 to the LaserJet 4 printer.
          
     LEGEND: Ec = [Ctrl] [P] [Esc] in DOS EDIT
     
     
     EcE                           Resets the Printer.
     
     Ec%0B                         Enters HP-GL/2 mode.
     
     IN;                           Initializes HP-GL/2 mode.
     
     SP1;                          Selects pen number 1
                                   (black). Even though
                                   there is no physical pen,
                                   the SP command must be
                                   used to enable printing.
     
     PA1016,5080;                  Specifies the absolute
                                   point (1016,5080) as the
                                   starting location.
     
     PR;PD;                        Specifies relative
                                   plotting and puts the pen
                                   down.
     
     BZ1016,8128,5588,5080,4572,7112,
     4064,8128,7112,7620,7112,2032;     Draws a Bezier using
                                   the current position
                                   (1016,5080) as the first
                                   control point. The
                                   specified control points
                                   for the first curve are
                                   (1016,8128), (5588,5080),
                                   and (4572,7112). The
                                   second curve uses the
                                   last control point of the
                                   previous curve as the
                                   first control point
                                   (45,7112). The other
                                   three control points for
                                   the second curve are
                                   (4064,8128), (7112,7620),
                                   and (7112,2032).
     
     Ec%0A                         Enters PCL mode.
     
     EcE                           Sends a reset to end the
                                   job and eject the page.
     
            Copyright  Hewlett-Packard Co. 1993
   The information contained herein is subject to change
                      without notice.
   Hewlett-Packard shall not be liable for incidental or
  consequential damages in connection with the use of this
                         material.
     


file: /Techref/language/pcl/lj1884.asc, 2KB, , updated: 1993/11/15 17:13, local time: 2024/10/8 13:33,
TOP NEW HELP FIND: 
44.220.251.236:LOG IN
©2024 PLEASE DON'T RIP! THIS SITE CLOSES OCT 28, 2024 SO LONG AND THANKS FOR ALL THE FISH!

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF="http://techref.massmind.org/Techref/language/pcl/lj1884.asc"> language pcl lj1884</A>

Did you find what you needed?

 

Welcome to massmind.org!

 

Welcome to techref.massmind.org!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .