please dont rip this site

Stepper Motor wiring

How to figure out the internal wiring of a stepper motor using a meter and a battery

Also see: other methods if figuring out stepper motor wiring

Bill Krause says:

I use a sure-fire technique for identifying two-phase stepper motor wiring (5,6,8 wire) including the order of the phases that requires only a d-cell battery, or a battery plus an ohmmeter. This works because if you excite a portion of one winding (from center-tap to one end ("phase") of a phase winding on a 5 or 6 wire motor, or one of the half-windings on an 8-wire motor) AND excite equally AND IN THE OPPOSITE POLARITY the other portion of that same winding (from center tap to the other end ("phase") of the same winding in a 5 or 6 wire motor, or the other half-winding associated with the same phase on an 8-wire motor) the motor will turn freely because the net excitation to the stator is zero. This situation will only occur when you are exciting two half-windings of the SAME PHASE in this manner. Therefore using this method you can sort out center-taps, associated half-windings, winding polarities, and phase association in the motor.

(In case you're wondering; when you short the two outside ends of a winding in a 5 or 6 wire motor and then apply excitation (the battery) across the center-tap and the shorted ends, you are applying excitation to the half-windings in parallel, OPPOSED POLARITY. If you draw a schematic of the hookup this becomes evident.)

Here are examples for 6 and 8 wire motors (I'll use the battery+ohmmeter method, because any old ohmmeter will work and almost everybody has one)

6 Wire Motors: With the ohmmeter, separate the wires into two groups of three (there'll be continuity among the three in a group, but no continuity between the groups) {ed: or use the method above to find the groups without a meter}

As you are testing, make sure that none of the motor wires are shorted together, other than the ones specified in the test.

Arbitrarily label the wires in one set a, b, and c.

Twist together a and c and hold them to one side of the battery while holding b to the other side. Does the motor turn easily?

Twist together leads b and c and connect them to one side of the battery and lead a to the other. Motor turn easily?

Twist together leads a and b and connect them to one side of the battery and c to the other. Motor turn easily?

Repeat the labelling and test sequence for the other set of wires. (see Stepper Motor Connection Options for all the different ways you can hook your motor up)

8 Wire: Take your ohmmeter and find the pairs of leads that have continuity between them and those four pairs are the two windings (each split in half). Just to make sure you don’t get snookered, measure between one wire of one winding and one wire of all the other windings and make sure you don’t have continuity there. Label the four pairs of leads: a, b; c,d; e,f; g,h.{ed: or use the method above to find the groups without a meter}

Make sure none of the motor wires are shorted together.

Turn the motor shaft and note how difficult (or easy) it is to turn.

Hold wires a and b to the ends of the battery. Note how hard the shaft turns (it should turn a lot harder than before).

{ed: In these next 6 tests, 5 should result in hard rotation and just one should allow the shaft to rotate easier than it did with a and b connected to the battery and almost as easy as it did without the battery. It's difficult to reliably hold the wires to the battery and feel the shaft turning at the same time; use a battery holder with wire clips or some other hands free system to reliably connect the wires.}

1. Twist lead a to c and lead b to d. Hold leads to battery. Does the shaft turn more easily then when power was applied?

2. Twist a to d and b to c. Connect battery. Rotate easier?

3. Twist a to e and b to f. Connect battery. Rotate easier?

4. Twist a to f and b to e. Connect battery. Rotate easier?

5. Twist a to g and b to h. Connect battery. Rotate easier?

6. Twist a to h and b to g. Connect battery. Rotate easier?

At this point let’s say you have successfully identified leads 1,2,3,4. Now to identify leads 5,6,7,8. Put leads 1,2,3,4 out of the way, but make sure they are not shorted together.

Relabel the remaining leads as a,b,c,d. {ed: you might be left with c,d,e,f or c,d,g,h from the first set of test; that doesn't matter. In any case, remove those old lables and relable the remaining wires a,b,c,d.}

Repeat the part of the testing above that involves a,b,c,d, but use lead numbers 5,6,7,8 for your results instead of 1,2,3,4.

{ed: Once you have all the wires numbered,
1 is A+
2 is A+'
3 is A-'
4 is A-
5 is B+
6 is B+'
7 is B-'
8 is B-

+}

(see Stepper Motor Connection Options for all the different ways you can hook your motor up)

These tests are sure-fire and work every time. Hope this helps

Motor wiring diagrams (for reference)

See also:

NEW! Roman Black's Linistep 1. stepper controller kit Proceeds support PICList.com

Code:


file: /Techref/io/stepper/wiresmeterbattery.htm, 8KB, , updated: 2019/12/19 17:41, local time: 2024/3/28 15:41,
TOP NEW HELP FIND: 
34.229.50.161:LOG IN

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF="http://techref.massmind.org/Techref/io/stepper/wiresmeterbattery.htm"> Stepper Motor wiring with meter and battery</A>

After you find an appropriate page, you are invited to your to this massmind site! (posts will be visible only to you before review) Just type a nice message (short messages are blocked as spam) in the box and press the Post button. (HTML welcomed, but not the <A tag: Instead, use the link box to link to another page. A tutorial is available Members can login to post directly, become page editors, and be credited for their posts.


Link? Put it here: 
if you want a response, please enter your email address: 
Attn spammers: All posts are reviewed before being made visible to anyone other than the poster.
Did you find what you needed?

 

Welcome to massmind.org!

 

Welcome to techref.massmind.org!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .